SAMPLE Clause

The SAMPLE clause allows for approximated SELECT query processing.

When data sampling is enabled, the query is not performed on all the data, but only on a certain fraction of data (sample). For example, if you need to calculate statistics for all the visits, it is enough to execute the query on the 1/10 fraction of all the visits and then multiply the result by 10.

Approximated query processing can be useful in the following cases:

  • When you have strict timing requirements (like \<100ms) but you can’t justify the cost of additional hardware resources to meet them.
  • When your raw data is not accurate, so approximation does not noticeably degrade the quality.
  • Business requirements target approximate results (for cost-effectiveness, or to market exact results to premium users).

Note

You can only use sampling with the tables in the MergeTree family, and only if the sampling expression was specified during table creation (see MergeTree engine).

The features of data sampling are listed below:

  • Data sampling is a deterministic mechanism. The result of the same SELECT .. SAMPLE query is always the same.
  • Sampling works consistently for different tables. For tables with a single sampling key, a sample with the same coefficient always selects the same subset of possible data. For example, a sample of user IDs takes rows with the same subset of all the possible user IDs from different tables. This means that you can use the sample in subqueries in the IN clause. Also, you can join samples using the JOIN clause.
  • Sampling allows reading less data from a disk. Note that you must specify the sampling key correctly. For more information, see Creating a MergeTree Table.

For the SAMPLE clause the following syntax is supported:

SAMPLE Clause SyntaxDescription
SAMPLE kHere k is the number from 0 to 1.

The query is executed on k fraction of data. For example, SAMPLE 0.1 runs the query on 10% of data. Read more SAMPLE n Here n is a sufficiently large integer.The query is executed on a sample of at least n rows (but not significantly more than this). For example, SAMPLE 10000000 runs the query on a minimum of 10,000,000 rows. Read more SAMPLE k OFFSET m Here k and m are the numbers from 0 to 1.The query is executed on a sample of k fraction of the data. The data used for the sample is offset by m fraction. Read more

SAMPLE K

Here k is the number from 0 to 1 (both fractional and decimal notations are supported). For example, SAMPLE 1/2 or SAMPLE 0.5.

In a SAMPLE k clause, the sample is taken from the k fraction of data. The example is shown below:

  1. SELECT
  2. Title,
  3. count() * 10 AS PageViews
  4. FROM hits_distributed
  5. SAMPLE 0.1
  6. WHERE
  7. CounterID = 34
  8. GROUP BY Title
  9. ORDER BY PageViews DESC LIMIT 1000

In this example, the query is executed on a sample from 0.1 (10%) of data. Values of aggregate functions are not corrected automatically, so to get an approximate result, the value count() is manually multiplied by 10.

SAMPLE N

Here n is a sufficiently large integer. For example, SAMPLE 10000000.

In this case, the query is executed on a sample of at least n rows (but not significantly more than this). For example, SAMPLE 10000000 runs the query on a minimum of 10,000,000 rows.

Since the minimum unit for data reading is one granule (its size is set by the index_granularity setting), it makes sense to set a sample that is much larger than the size of the granule.

When using the SAMPLE n clause, you do not know which relative percent of data was processed. So you do not know the coefficient the aggregate functions should be multiplied by. Use the _sample_factor virtual column to get the approximate result.

The _sample_factor column contains relative coefficients that are calculated dynamically. This column is created automatically when you create a table with the specified sampling key. The usage examples of the _sample_factor column are shown below.

Let’s consider the table visits, which contains the statistics about site visits. The first example shows how to calculate the number of page views:

  1. SELECT sum(PageViews * _sample_factor)
  2. FROM visits
  3. SAMPLE 10000000

The next example shows how to calculate the total number of visits:

  1. SELECT sum(_sample_factor)
  2. FROM visits
  3. SAMPLE 10000000

The example below shows how to calculate the average session duration. Note that you do not need to use the relative coefficient to calculate the average values.

  1. SELECT avg(Duration)
  2. FROM visits
  3. SAMPLE 10000000

SAMPLE K OFFSET M

Here k and m are numbers from 0 to 1. Examples are shown below.

Example 1

  1. SAMPLE 1/10

In this example, the sample is 1/10th of all data:

[++------------]

Example 2

  1. SAMPLE 1/10 OFFSET 1/2

Here, a sample of 10% is taken from the second half of the data.

[------++------]